Search:

Type: Posts; User: DeanS15

Page 1 of 16 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    16
    Views
    6,332

    I'm not sure other than hand cranking the engine...

    I'm not sure other than hand cranking the engine until the cam lobe is down and then seeing if it can be compressed and return. If it was me and the engine had sat for a long time then pulling the...
  2. Replies
    16
    Views
    6,332

    Looks like spray bars may be partially blocked as...

    Looks like spray bars may be partially blocked as well, there should not be rust on your camshafts. Could be a stuck valve broke the arm or just fatigue and lack of oil. ...
  3. S15 signal comes from the differential, s14 comes...

    S15 signal comes from the differential, s14 comes from the gear driven sensor on the gearbox from memory. In other words, if you swapped a 5 speed into a S15 you'll still have it just leave the...
  4. Replies
    2
    Views
    5,354

    As far as I can remember the bumpers are just...

    As far as I can remember the bumpers are just held on with 6 or 8mm push clips along the tops and in the arch liners and some m6 bolts/ tapping screws inside the wheel wells. Maybe some m8 in there...
  5. Replies
    1,503
    Views
    186,018

    You must be joking mte the silvia looked after me...

    You must be joking mte the silvia looked after me compared to this seeing as they've got no traction control or esp etc
  6. Replies
    1,503
    Views
    186,018

    It's kind of like the silvia, same colour, rwd...

    It's kind of like the silvia, same colour, rwd and powerful just a LOT heavier!
  7. Replies
    1,503
    Views
    186,018

    Glad to hear it, the work you're doing looks...

    Glad to hear it, the work you're doing looks great and the premises looks really nice. Family are good thanks, got a 7 year old now that's almost how long I've been out of the silv! A while back I...
  8. Replies
    16
    Views
    6,332

    There was a time when if there were any running...

    There was a time when if there were any running issues the plugs, leads and dizzy were usually the culprit but as time has gone on cars simply don't have them any more now there is dis and coil on...
  9. Replies
    3
    Views
    5,982

    I would get the base timing checked as that can...

    I would get the base timing checked as that can reduce power across the whole rev range and cause a lot of detonation that you might not notice. Then the usual check for boost leaks, make sure the...
  10. Replies
    16
    Views
    6,332

    Sounds like a miss... Is that a distributor on...

    Sounds like a miss... Is that a distributor on the spec s? If it is I'd be looking at that for sure. If not might be worth a compression test if there's definitely fuel and spark, also the usual make...
  11. Replies
    1,503
    Views
    186,018

    Amazing beautiful work man, always check in here...

    Amazing beautiful work man, always check in here to one day see the finished article and the work you've done between visits never, ever disappoints!

    Hope you're well and business is good.
  12. Replies
    1,503
    Views
    186,018

    I love the clocks with 'mine' written on them...

    I love the clocks with 'mine' written on them lol. Did you have the inlet made custom mate?
  13. Replies
    1,503
    Views
    186,018

    Where abouts is the new one the Chris? Not that I...

    Where abouts is the new one the Chris? Not that I ever got down to the old place but I'd love to drop by and say hello when it's up and running, been a long time.
  14. Replies
    1,503
    Views
    186,018

    Would seem like a good time to stitch it all...

    Would seem like a good time to stitch it all :cool:
  15. Replies
    1,503
    Views
    186,018

    Have you media blasted the front end mate? I...

    Have you media blasted the front end mate? I would of loved to have done that and taken it right back
  16. WTB: Not much help but I think there's a full list of...

    Not much help but I think there's a full list of the bolts in my build thread somewhere as the questions been asked before. Most of them you can pick up anywhere just 8.8 m12 and m10 bolts with a...
  17. Replies
    1,503
    Views
    186,018

    Very nice Chris. I keep checking in to see how...

    Very nice Chris. I keep checking in to see how you're getting on,all really nice quality parts as always. Is it me or is it real quiet on here these days? I thought the forum would get busier as more...
  18. Thread: Which Decat

    by DeanS15
    Replies
    7
    Views
    4,220

    From memory the s13 decat is the one you want,...

    From memory the s13 decat is the one you want, otherwise the flange orientation isn't right. I had an s13 decat with an s14 bellmouth turbo elbow and downpipe and it mated up to an s15 specific hks...
  19. Replies
    12
    Views
    1,631

    For discs I used a company called brakedepot and...

    For discs I used a company called brakedepot and got some grooved discs. They were fine and a good price but mine were for Z32 conversion, 200sx/s14/s15 look the same but use a solid disc. Mtec...
  20. Replies
    12
    Views
    1,631

    Conceptua tuning normally do all the parts you'd...

    Conceptua tuning normally do all the parts you'd need, they also rebuild them for you and do custom paint or they did when I used them.
  21. Replies
    4
    Views
    3,370

    Scotchlocks - get rid of them, they are utter...

    Scotchlocks - get rid of them, they are utter s**t. A lot of the time they don't give a good connection, other times they completely cut through the wire. If you want it to be a sound connection just...
  22. Replies
    1,503
    Views
    186,018

    What box you gonna run mate Z33?

    What box you gonna run mate Z33?
  23. Replies
    19
    Views
    1,499

    It's a good idea to use the nissan 2 bolt tabs...

    It's a good idea to use the nissan 2 bolt tabs too for the manifold to turbo if the design let's you use them, that way once done up the nuts shouldn't be able to work loose easily - and if enough...
  24. Replies
    1,503
    Views
    186,018

    I will Chris cheers for the invite! As I don't...

    I will Chris cheers for the invite! As I don't circle the forum too much these days and I'm not on Facebook if you remember maybe drop me a pm, I'd certainlywant to drop in. Would be good to see...
  25. Replies
    1,503
    Views
    186,018

    Really pleased everything has taken off! I see...

    Really pleased everything has taken off! I see you're taking on staff and expanding, that's awesome mate, really happy for you and hope it continues to go from strength to strength :cool:
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4